How To Install Door Hinges? – A Step By Step Guide

How To Install Door Hinges? – A Step By Step Guide

Want to learn the easy steps about how to install hinges on a door or how to install hinges on a new door jamb? If you already have done it before then it’s okay but by reading these articles you will get the complete ideas of easy steps of installing the hinges on a door.

The installation of the hinges on a door or a cabinet door is pretty easy. But you have to know the actual processes. By following the right process you can complete the task within a very short time and error-free. Carefully follow the steps and successfully install the door hinges.

10 Easy Steps: How To Install Hinges On A New Door Jamb?

10 Easy Steps: How To Install Hinges On A New Door Jamb?

Following the right stages of installing the hinges on the door does not only speed up the process. It’s also helping you to create a durable job.

Before you start set out your hinges and measure up the size twice. Then cut it once. Take the measurements for each of the mounting holes with your measuring tape and start your project work.

This guide will give you complete ideas of how to install hinges on a door.

Step 1: Measure The Distance Between Doors

Measure The Distance Between Doors

Measure up the doors by putting the measuring tape between each door’s hinges. Make sure you take the measurements from the hinge to the hinges from both sides of each door. Make sure you are measuring the hinge to hinge from both sides of each door. 

This measurement should be accurate and down to the friction of each inch. If you do not measure up the distances you will have trouble installing the hinge correctly.

Step 2: Choose The Right Hinge Type

Choose The Right Hinge Type

There are varieties of hinges available in the market some look simple also some have decorative sides. That included different fine cabinetry and furniture. But also have some of the household doors that are known as the standard hinge. 

Most of the interior closet doors feature the standard sizes of hinges and are suitable for 360-degree movement facility. Standard-size exterior hinged doors attach at both ends and do not rotate.

Step 3: Mark Then Drill The Hole Spacing

Mark Then Drill The Hole Spacing

Mark the hole and spacing on each hinge. This will also allow you to align with each hinge along with the matching door jambs for installation. For doing this job try to insert a hinge pin into one hinge then slide over and open the door and push up against the door jamb. 

Repeat the process for the other four hinges and drill the corresponding holes into the doors. Use a drill of 1/8-inch bit.

Step 4: Test The Hinge Fit

Test The Hinge Fit

Start with test fitting your door hinge. Even after taking the actual measurement, it can’t be always error-free. You can end up breaking it make sure you are working it correctly right before proceeding with the installation.

Step 5: Attach The Hinge

Attach The Hinge

Assemble and install the door hinges on the frame. Then lift it to the door into the position on the hinges and tighten up the screws. How to install hinges on a door? Read through the end and know the exact process. The hinge should be installed right below and above each door center. Check out the hardware pack for specific instructions.

Step 6: Adjust The Gap

Adjust The Gap

Door hinges are standardized so that they can fit most of the doors. If your door is still off you can start by adjusting the gap between it and your new hinge by losing up and tightening up the screws.

You can organize them perfectly and ensure whether the door closes or opens. Repeat the process for every hinge that you are installing. Take out your wrench and make the necessary adjustments as required.

Step 7: Prime, And Paint

Once you are door prepared it’s time to paint it. For a nice finishing spray, you can roll on two coats of paint and allow it to dry. You can also use a brush and apply some finishing stains before paint application. Sometimes people like to do those steps before installing the door hinges.

Step 8: Assemble Your Interior Side Of The Door

Examine the pre-drilled holes and verify the measurements. You will going to need a power screwdriver and hex key. Hex keys come with tape-measuring features and by purchasing the hinges you can find them easily at home.

Step 9: Secure The Interior Side Of The Door

Place the screws through the hinge top into the door frame. Secure it by twisting the screwdriver and tighten up. Repeat the same action for the other side of the door. Close the door and test the hinge. If the door won’t close repeat the installation process again.

If you are facing any trouble in the process of how to install hinges on a cabinet door or facing challenges for larger size hinges then you can also install the hinges themselves or just contact the manufacturer directly. For any difficulty, it’s always better to consult with professionals.

In Conclusion

hinges on a door

Get ideas on how to install hinges on a door. Fitting the door hinges requires very precise and careful attention to detail. By following these easy step-by-step instructions you can ensure that door hinges are seated correctly and allow smooth operations and secure fit. What is your opinion? Which types of installation process you are going to follow? Comment back to us and let us know your personal tips.

Also Read:-

About The Author

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top